help tplink3220v1 ripristino firmware originale
- Creatore Discussione fumore67
- Data di inizio
Loop
Membro noto
Ciao ti serve l’interfaccia seriale: TP-Link TL-MR3420 & TL-MR3220 [Old OpenWrt Wiki]
Ti serve sempre la seriale …
cia0 o apena collegato il tutto e mi uscito questo per gli esperti cosa sicnifica vado bene o o o pure?
Codice:
U-Boot 1.1.4 (Jan 25 2011 - 12:09:11)
AP99 (ar7241 - Virian) U-boot
DRAM:
sri
ar7240_ddr_initial_config(133): virian ddr1 init
#### TAP VALUE 1 = 0xf, 2 = 0x10 [0x0: 0x1f]
32 MB
id read 0x100000ff
sector count = 64
Flash: 4 MB
Using default environment
In: serial
Out: serial
Err: serial
Net: ag7240_enet_initialize...
No valid address in Flash. Using fixed address
No valid address in Flash. Using fixed address
Virian MDC CFG Value ==> 4
: cfg1 0xf cfg2 0x7014
eth0: 00:03:7f:09:0b:ad
eth0 up
Virian MDC CFG Value ==> 4
: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
ATHRS26: resetting s26
ATHRS26: s26 reset done
eth1 up
eth0, eth1
Autobooting in 1 seconds
## Booting image at 9f020000 ...
Uncompressing Kernel Image ... OK
Starting kernel ...
OpenWrt kernel loader for AR7XXX/AR9XXX
Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org>
Looking for OpenWrt image... found at 0xbf022000
Decompressing kernel... done!
Starting kernel at 80060000...
[ 0.000000] Linux version 3.10.24 (openwrt@OpenWRT) (gcc version 4.6.4 (OpenW
rt/Linaro GCC 4.6-2013.05 r39155) ) #1 Sun Dec 22 23:59:53 MST 2013
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Atheros AR7241 rev 1
[ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:5.000
MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x01ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x01ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32
bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag
es: 8128
[ 0.000000] Kernel command line: board=TL-MR3220 console=ttyS0,115200 rootfs
type=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 28644k/32768k available (2323k kernel code, 4124k reserve
d, 610k data, 264k init, 0k highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[ 0.080000] pid_max: default: 32768 minimum: 301
[ 0.080000] Mount-cache hash table entries: 512
[ 0.090000] NET: Registered protocol family 16
[ 0.100000] MIPS: machine is TP-LINK TL-MR3220
[ 0.500000] registering PCI controller with io_map_base unset
[ 0.540000] bio: create slab <bio-0> at 0
[ 0.550000] PCI host bridge to bus 0000:00
[ 0.550000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[ 0.560000] pci_bus 0000:00: root bus resource [io 0x0000]
[ 0.560000] pci_bus 0000:00: No busn resource found for root bus, will use [b
us 00-ff]
[ 0.570000] pci 0000:00:00.0: fixup device configuration
[ 0.570000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1000ffff 64bi
t]
[ 0.580000] pci 0000:00:00.0: using irq 40 for pin 1
[ 0.580000] Switching to clocksource MIPS
[ 0.590000] NET: Registered protocol family 2
[ 0.590000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.600000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.610000] TCP: Hash tables configured (established 512 bind 512)
[ 0.610000] TCP: reno registered
[ 0.620000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.620000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.630000] NET: Registered protocol family 1
[ 0.650000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.660000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORIT
Y) (c) 2001-2006 Red Hat, Inc.
[ 0.670000] msgmni has been set to 55
[ 0.670000] io scheduler noop registered
[ 0.680000] io scheduler deadline registered (default)
[ 0.680000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.720000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[ 0.720000] console [ttyS0] enabled, bootconsole disabled
[ 0.720000] console [ttyS0] enabled, bootconsole disabled
[ 0.740000] ath79-spi ath79-spi: master is unqueued, this is deprecated
[ 0.740000] m25p80 spi0.0: found s25sl032p, expected m25p80
[ 0.750000] m25p80 spi0.0: s25sl032p (4096 Kbytes)
[ 0.760000] 5 tp-link partitions found on MTD device spi0.0
[ 0.760000] Creating 5 MTD partitions on "spi0.0":
[ 0.770000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.770000] 0x000000020000-0x000000126a00 : "kernel"
[ 0.780000] mtd: partition "kernel" must either start or end on erase block b
oundary or be smaller than an erase block -- forcing read-only
[ 0.790000] 0x000000126a00-0x0000003f0000 : "rootfs"
[ 0.800000] mtd: partition "rootfs" must either start or end on erase block b
oundary or be smaller than an erase block -- forcing read-only
[ 0.810000] mtd: device 2 (rootfs) set to be root filesystem
[ 0.820000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.820000] 0x0000002f0000-0x0000003f0000 : "rootfs_data"
[ 0.830000] 0x0000003f0000-0x000000400000 : "art"
[ 0.840000] 0x000000020000-0x0000003f0000 : "firmware"
[ 0.860000] libphy: ag71xx_mdio: probed
[ 1.410000] ag71xx-mdio.1: Found an AR7240/AR9330 built-in switch
[ 2.450000] eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[ 3.000000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd0
41, driver=Generic PHY]
[ 3.010000] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[ 3.020000] TCP: cubic registered
[ 3.020000] NET: Registered protocol family 17
[ 3.030000] Bridge firewalling registered
[ 3.030000] can: controller area network core (rev 20120528 abi 9)
[ 3.040000] NET: Registered protocol family 29
[ 3.040000] 8021q: 802.1Q VLAN Support v1.8
[ 3.060000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 3.070000] Freeing unused kernel memory: 264K (8033e000 - 80380000)
procd: Console is alive
procd: - watchdog -
procd: - preinit -
[ 6.280000] usbcore: registered new interface driver usbfs
[ 6.300000] usbcore: registered new interface driver hub
[ 6.300000] usbcore: registered new device driver usb
[ 6.320000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 6.340000] ehci-platform: EHCI generic platform driver
[ 6.340000] ehci-platform ehci-platform: EHCI Host Controller
[ 6.350000] ehci-platform ehci-platform: new USB bus registered, assigned bus
number 1
[ 6.350000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 6.380000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 6.390000] hub 1-0:1.0: USB hub found
[ 6.390000] hub 1-0:1.0: 1 port detected
[ 6.400000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 7.870000] eth0: link up (1000Mbps/Full duplex)
mount_root: jffs2 is ready
[ 9.700000] jffs2: notice: (332) jffs2_build_xattr_subsystem: complete buildi
ng xattr subsystem, 15 of xdatum (0 unchecked, 14 orphan) and 95 of xref (0 dead
, 84 orphan) found.
[ 9.730000] eth0: link down
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
[ 10.710000] NET: Registered protocol family 10
[ 10.730000] nf_conntrack version 0.5.0 (451 buckets, 1804 max)
[ 10.740000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 10.770000] Loading modules backported from Linux version master-2013-11-05-0
-gafa3093
[ 10.780000] Backport generated by backports.git backports-20130802-0-gdb67a3f
[ 10.790000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 10.840000] xt_time: kernel timezone is -0000
[ 10.880000] cfg80211: Calling CRDA to update world regulatory domain
[ 10.880000] cfg80211: World regulatory domain updated:
[ 10.890000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gai
n, max_eirp)
[ 10.900000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 20
00 mBm)
[ 10.900000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 20
00 mBm)
[ 10.910000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 20
00 mBm)
[ 10.920000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 20
00 mBm)
[ 10.930000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 20
00 mBm)
[ 10.930000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0
mBm)
[ 11.020000] PPP generic driver version 2.4.2
[ 11.020000] NET: Registered protocol family 24
[ 11.080000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[ 11.120000] ieee80211 phy0: Atheros AR9285 Rev:2 mem=0xb0000000, irq=40
[ 11.130000] cfg80211: Calling CRDA for country: US
[ 11.130000] cfg80211: Regulatory domain changed to country: US
[ 11.140000] cfg80211: DFS Master region FCC
[ 11.140000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gai
n, max_eirp)
[ 11.150000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 27
00 mBm)
[ 11.160000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 17
00 mBm)
[ 11.170000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (300 mBi, 24
00 mBm)
[ 11.180000] cfg80211: (5490000 KHz - 5600000 KHz @ 80000 KHz), (300 mBi, 24
00 mBm)
[ 11.180000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 24
00 mBm)
[ 11.190000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 30
00 mBm)
[ 11.200000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 40
00 mBm)
procd: - init complete -
[ 18.540000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 18.540000] device eth0 entered promiscuous mode
[ 18.550000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 18.560000] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 19.640000] eth0: link up (1000Mbps/Full duplex)
[ 19.640000] br-lan: port 1(eth0) entered forwarding state
[ 19.650000] br-lan: port 1(eth0) entered forwarding state
[ 19.650000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 19.660000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 21.650000] br-lan: port 1(eth0) entered forwarding state
#d>>^F~v ‘óæHÌ&fææææ^F^@^@Please press Enter to activate this con
sole.
y^@^@y^@^@^O^@^@@$‘I¿>^^if“fæææ^F^@^@Please press Enter to activate this console
.
Ma scusa perchè non l’hai detto prima che stavi usando OpenWrt?
Vedo come data Sun Dec 22 23:59:53 MST 2013, l’hai compilato tu o hai scaricato uno snapshot dal trunk?
La versione scaricata dal trunk non ha installato LuCI e quindi niente interfaccia web.
Vuoi rimettere il firmware originale?
Vedo come data Sun Dec 22 23:59:53 MST 2013, l’hai compilato tu o hai scaricato uno snapshot dal trunk?
La versione scaricata dal trunk non ha installato LuCI e quindi niente interfaccia web.
Vuoi rimettere il firmware originale?
Puoi usare il failsafe per ritornare al firmware originale e non dovrebbe servire la seriale.
Scarica il firmware originale SENZA la stringa “boot” nel nome del file e facendo attenzione alla versione hardware, nel tuo caso va bene questo: http://www.tp-link.com/Resources/software/TL-MR3220_V1_120523.zip
Scarica un file server http (ti consiglio HFS) e Putty, segui questi passaggi:
Scarica il firmware originale SENZA la stringa “boot” nel nome del file e facendo attenzione alla versione hardware, nel tuo caso va bene questo: http://www.tp-link.com/Resources/software/TL-MR3220_V1_120523.zip
Scarica un file server http (ti consiglio HFS) e Putty, segui questi passaggi:
- Scollega la seriale, disattiva il wireless, imposta la scheda di rete lan del pc con ip statico 192.168.1.10 e collega il router usando una porta lan.
- Accendi il router e premi il tasto QSS non appena il led SYS inizia a lampeggiare, OpenWrt andrà in FailSafe.
- Estrai il firmware che hai scaricato e rinominalo per comodità in firmware.bin
- Apri HFS, tasto destro nella parte sinistra e poi add files, seleziona il firmware (file firmware.bin)
- Apri Putty e collegati usando il protocollo telnet al router (ip 192.168.1.1)
- Scrivi il seguente comando e dai invio
Codice:
cd /tmp- Scrivi il seguente comando e dai invio
Codice:
wget http://192.168.1.10/firmware.bin- Scrivi il seguente comando e dai invio
Codice:
mtd -r write /tmp/firmware.bin firmware- Terminata la scrittura il router dovrebbe riavviarsi con il firmware orginale.
ciao effeti o fatto come ai detto. ecco cosa esce BusyBox v1.19.4 (2013-12-22 23:48:36 MST) built-in shell (ash)
Enter ‘help’ for a list of built-in commands.
| |.-----.-----.-----.| | | |.----.| |_
root@OpenWrt:/# cd /tmp
root@OpenWrt:/tmp# wget http://192.168.1.10/firmware.bin
Connecting to 192.168.1.10 (192.168.1.10:80)
wget: server returned error: HTTP/1.1 404 Not Found
root@OpenWrt:/tmp# mtd -r write /tmp/firmware.bin firmware
Couldn’t open image file: /tmp/firmware.bin!
root@OpenWrt:/tmp# non riesco a mandare il firmware ? qualche consiglio?
Enter ‘help’ for a list of built-in commands.
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -| || | | || || |
|_____|| |||||___||| |____|
|| W I R E L E S S F R E E D O M
BARRIER BREAKER (Bleeding Edge, r39155)
- 1/2 oz Galliano Pour all ingredients into
- 4 oz cold Coffee an irish coffee mug filled
- 1 1/2 oz Dark Rum with crushed ice. Stir.
- 2 tsp. Creme de Cacao
root@OpenWrt:/# cd /tmp
root@OpenWrt:/tmp# wget http://192.168.1.10/firmware.bin
Connecting to 192.168.1.10 (192.168.1.10:80)
wget: server returned error: HTTP/1.1 404 Not Found
root@OpenWrt:/tmp# mtd -r write /tmp/firmware.bin firmware
Couldn’t open image file: /tmp/firmware.bin!
root@OpenWrt:/tmp# non riesco a mandare il firmware ? qualche consiglio?
Il led SYS lampeggia molto velocemente? (FailSafe)
Se sei collegato con telnet la connessione LAN dovrebbe essere ok, il problema è in qualche impostazione di HFS o nel firewall di windows.
Ma non è che hai altre connessioni attive?
Apri HFS nella barra degli indirizzi in alto devi vedere come indirizzo http://192.168.1.10 se hai attivo il wi-fi o altre connessioni l’indirizzo cambia, devi disattivarle e lasciare solo la LAN.
Se sei collegato con telnet la connessione LAN dovrebbe essere ok, il problema è in qualche impostazione di HFS o nel firewall di windows.
Ma non è che hai altre connessioni attive?
Apri HFS nella barra degli indirizzi in alto devi vedere come indirizzo http://192.168.1.10 se hai attivo il wi-fi o altre connessioni l’indirizzo cambia, devi disattivarle e lasciare solo la LAN.
Dovrebbe continuare a lampeggiare, quando diventa fisso vuol dire che ha finito di “caricare” il firmware quindi non sei in failsafe.
Spegni il router, accendilo, il led sys inizia a lampeggiare, aspetti 2 secondi e premi qss.
Comunque se riesci ad entrare con telnet non è questo il problema.
ora mi esce questo …Welcome to GoodTech Systems Telnet Server for Windows NT/2000/XP (Evaluation Cop
y)
(C) Copyright 1996-2002 GoodTech Systems, Inc.
Login username: cd /tmp
Login password: *************************************
Domain name: mtd -r write /tmp/firmware.bin firmware
Authentication is in progress…
Login failed…
Login username:
y)
(C) Copyright 1996-2002 GoodTech Systems, Inc.
Login username: cd /tmp
Login password: *************************************
Domain name: mtd -r write /tmp/firmware.bin firmware
Authentication is in progress…
Login failed…
Login username:
